WIDIA - Полный каталог инструмента - 2017
для размещения заказа - zakaz@widiahanita.ru
High-Performance Solid Carbide End Mills • Hard Materials
Application Data • Series D618 • Vision Plus™
Series D618 • Vision Plus
Side Milling (A)
TiAlN
Recommended feed per tooth (fz = mm/th) for side milling (A).
Material
Group
3
P
4
1
2
H
3
4
A
Cutting Speed — vc
m/min
ap ae min
max
2 x D 0,15 x D 120 – 160
2 x D 0,15 x D 90 – 150
2 x D 0,15 x D 80 – 140
2 x D 0,15 x D 70 – 120
2 x D 0,1 x D 60 – 90
2 x D 0,05 x D 50 – 70
mm
fz
fz
fz
fz
fz
fz
3,0
0,019
0,017
0,017
0,013
div class="txt" style="position:absolute; left:274px; top:260px;">0,010
0,007
4,0
0,026
0,024
0,024
0,018
0,014
0,009
5,0
0,033
0,030
0,030
0,022
0,018
0,012
D1 — Diameter
6,0
0,040
0,036
0,036
0,027
0,021
0,014
8,0
0,055
0,049
0,049
0,037
0,029
0,019
10,0
0,067
0,059
0,059
0,044
0,035
0,023
12,0
0,077
0,069
0,069
0,051
0,041
0,027
16,0
0,096
0,084
0,084
0,063
0,051
0,034
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for nishing applications or for lower hardness (machinability) within group.
For better surface nish, reduce feed per tooth.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on diameters >12mm.
20,0
0,111
0,097
0,097
0,071
0,059
0,039
Series 422837 422831 • Vision Plus
Application Data • Series 422837 422831 • Vision Plus™
Side Milling (A)
K10UF-DCHP
AlTiN
Recommended feed per tooth (fz = mm/th) for side milling (A).
Material
Group
A
ap ae
Cutting Speed — vc
m/min
min max
mm
6,0
D1 — Diameter
8,0 10,0 12,0 16,0 20,0
3 1,5 x D 0,2 x D 120 – 160
P
4 1,5 x D 0,2 x D 90 – 150
fz 0,040 0,055 0,067 0,077 0,096 0,111
fz 0,036 0,049 0,059 0,069 0,084 0,097
1 1,5 x D 0,2 x D
80 – 140
fz 0,036 0,049 0,059 0,069 0,084 0,097
2 1,5 x D 0,15 x D 60 – 80
H
3 1,5 x D 0,1 x D 50 – 70
fz 0,027 0,037 0,044 0,051 0,063 0,071
fz 0,021 0,029 0,035 0,041 0,051 0,059
4 1,5 x D 0,05 x D 40 – 60
fz 0,014 0,019 0,023 0,027 0,034 0,039
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for nishing applications or for lower hardness (machinability) within group.
For better surface nish, reduce feed per tooth.
For Series 422831, ap max = 2,5 x D by 50% ae.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on diameters >12mm.
25,0
0,125
0,107
0,107
0,078
0,067
0,044
zakaz@widiahanita.ru
www.widiahanita.ru
O203