WIDIA - Полный каталог инструмента - 2017
для размещения заказа - zakaz@widiahanita.ru
Indexable Drills
Application Data • Top Cut 4™
Top Cut 4 • Steel • 2 x D/3 x D • Speed Chart • Metric
Top Cut 4
Insert Size E
Recommended Cutting Speed by Diameter (m/min)
Insert Size F
Insert Size G
Insert Size H
TCF120405EC
TCF100408EP
30,00–36,99mm
TCF150406FC
TCF120412FP
37,00–45,99mm
TCF180508GC
TCF150512GP
46,00–56,99mm
TCF210608HC
TCF180614HP
57,00–68,00mm
Material
Pocket
Group Condition Seat Geometry Grade min Start max min Start max min Start max min Start
P V36 WU25CH
S 160 180 260 160 180 260 160 180 260 160 180
C V36 WU40PH
1U
P V36 WU40PH
140 170 250 140 170 250 140 170 250 140 170
C V36 WU40PH
P V36 WU40PH
I 140 170 240 140 170 240 140 170 240 140 170
C V36 WU40PH
P V34 WPK10CH
S 160 190 280 160 190 280 160 190 280 160 190
C V34 WU40PH
2U
P V34 WU25CH
150 180 260 150 180 260 150 180 260 150 180
C V34 WU40PH
P V34 WU40PH
I 140 170 240 140 170 240 140 170 240 140 170
C V34 WU40PH
P V34 WPK10CH
S 160 200 310 160 200 310 160 200 310 160 200
C V34 WU40PH
3U
P V34 WU25CH
150 200 280 150 200 280 150 200 280 150 200
C V34 WU40PH
P V34 WU40PH
I 140 180 260 140 180 260 140 180 260 140 180
C V34 WU40PH
P
P V34 WPK10CH
S 160 200 310 160 200 310 160 200 310 160 200
C V34 WU40PH
4U
P V34 WU25CH
150 200 280 150 200 280 150 200 280 150 200
C V34 WU40PH
P V34 WU40PH
I 140 180 260 140 180 260 140 180 260 140 180
C V34 WU40PH
P V36 WU25CH
S 160 180 250 160 180 250 160 180 250 160 180
C V36 WU40PH
5U
P V36 WU40PH
150 170 240 150 170 240 150 170 240 150 170
C V36 WU40PH
P V36 WU40PH
I 140 160 220 140 160 220 140 160 220 140 160
C V36 WU40PH
P V36 WU25CH
S 150 170 210 150 170 210 150 170 210 150 170
C V36 WU40PH
6U
P V36 WU40PH
140 160 200 140 160 200 140 160 200 140 160
C V36 WU40PH
P V36 WU40PH
I 120 140 190 120 140 190 120 140 190 120 140
C V36 WU40PH
NOTE: For 4 x D, it is highly recommended to start with feed and speed values reduced by 10% less than above recommendations.
For 5 x D, diameter range 12–23,99mm (insert sizes A to C), it is highly recommended to start with feed and speed values reduced by 20% less than
above recommendations.
For 5 x D, diameter range 24–68mm (insert sizes D to H), it is highly recommended to start with feed and speed values reduced by 15% less than
above recommendations.
For 4 x D and 5 x D, it is recommended to reduce the feed rate during entry and exit by 30–50%.
max
260
250
240
280
260
240
310
280
260
310
280
260
250
240
220
210
200
190
Condition: S = stable conditions,
U = unstable cutting conditions,
I = interrupted cutting conditions
Pocket Seat: P = periphery insert,
C = centre insert
zakaz@widiahanita.ru
www.widiahanita.ru
V27