WIDIA - Полный каталог инструмента - 2017
Speed and Feed Chart
Positive Inserts • Metric
для размещения заказа - zakaz@widiahanita.ru
Material
Group
ap [mm]
f [mm/rev]
0/1
2
P
3
4
5
6
ap [mm]
f [mm/rev]
M1
2
3
ap [mm]
f [mm/rev]
K1
2
3
ap [mm]
f [mm/rev]
1
2
N3
4
5
6
7
ap [mm]
f [mm/rev]
1
S
2
3
4
ap [mm]
f [mm/rev]
1
H
2
3
4
Cutting Speed — vc
m/min
C2 C25 C3 CG5 CG55 CG6
min Start max min Start max min Start max min Start max min Start max min Start max
– – – – – – – – – 0,051 – 0,300 0,051 – 0,300 0,051 – 0,300
– – – – – – – – – 0,025 – 0,300 0,025 – 0,300 0,025 – 0,300
– – – – – – – – – 95 115 140 105 130 155 125 155 190
– – – – – – – – – 60 75 90 65 85 100 80 100 125
– – – – – – – – – 60 75 90 65 85 100 80 100 125
– – – – – – – – – 45 60 70 50 65 80 65 80 95
– – – – – – – – – 60 75 90 65 85 100 80 100 125
– – – – – – – – – 40 50 60 45 55 70 55 65 80
0,051 – 0,300 0,051 – 0,300 0,051 – 0,300 0,051 – 0,300 0,051 – 0,300 0,051 – 0,300
0,025 – 0,300 0,025 – 0,300 0,025 – 0,300 0,025 – 0,300 0,025 – 0,300 0,025 – 0,300
55 70 80 60 80 95 60 80 95 75 90 110 80 100 120 95 115 140
50 60 75 55 70 85 55 70 85 65 80 100 75 90 110 85 105 125
35 45 55 45 50 65 45 50 65 50 60 75 55 65 80 60 80 95
0,051 – 0,300 0,051 – 0,300 0,051 – 0,300 0,051 – 0,300 0,051 – 0,300 0,051 – 0,300
0,025 – 0,300 0,025 – 0,300 0,025 – 0,300 0,025 – 0,300 0,025 – 0,300 0,025 – 0,300
50 65 80 60 70 85 60 70 85 60 75 90 65 80 100 75 90 110
65 80 100 75 90 110 75 90 110 75 95 115 85 105 125 95 115 140
50 60 75 55 65 80 55 65 80 55 70 80 60 75 90 65 85 100
0,051 – 0,300 0,051 – 0,300 0,051 – 0,300 0,051 – 0,300 0,051 – 0,300 – – –
0,025 – 0,300 0,025 – 0,300 0,025 – 0,300 0,025 – 0,300 0,025 – 0,300 – – –
400 505 605 400 505 605 400 505 605 400 505 605 445 555 665 – – –
295 370 440 295 370 445 295 370 445 295 370 445 325 405 490 – – –
70 85 105 70 85 105 70 85 105 85 105 125 90 115 135 – – –
310 380 465 310 385 465 310 385 465 140 175 210 155 190 230 – – –
145 185 220 145 185 220 145 185 220 175 220 265 195 240 290 – – –
140 175 210 140 175 210 140 175 210 170 210 255 185 235 280 – – –
240 295 355 240 300 360 240 300 360 245 305 365 265 335 400 – – –
0,025 – 0,200 0,025 – 0,200 0,025 – 0,200 0,025 – 0,200 0,025 – 0,200 – – –
0,025 – 0,127 0,025 – 0,127 0,025 – 0,127 0,025 – 0,127 0,025 – 0,127 – – –
30 35 45 30 35 45 30 35 45 30 35 45 35 40 50 – – –
25 30 35 25 30 35 25 30 35 25 30 35 25 35 40 – – –
25 30 35 25 30 35 25 30 35 30 40 50 35 45 55 – – –
25 30 35 25 30 35 25 30 35 – – – – – – – – –
––––––––––––––––––
––––––––––––––––––
––––––––––––––––––
––––––––––––––––––
––––––––––––––––––
––––––––––––––––––
NOTE: Speed and feed rates and depth of cut may vary depending on materials and machining conditions including, but not
limited to, tool overhang, tool size, and nished surface requirements.
D40
zakaz@widiahanita.ru
www.widiahanita.ru