WIDIA - Полный каталог инструмента - 2017
для размещения заказа - zakaz@widiahanita.ru
High-Performance Solid Carbide End Mills • VariMill™
Application Data • Series 77NE • VariMill III™ ER • Victory™ Grades
Series 77NE • VariMill III ER • With Neck • Semi-Finishing • Victory Grades
Side Milling (A)
WS15PE
Recommended feed per tooth (fz = mm/th) for side milling (A).
Material
Group
A
ap ae
Cutting Speed — vc
m/min
min max
mm
10,0
D1 — Diameter
12,0 16,0 18,0
20,0
4
P
5
Ap1 max
Ap1 max
0,3 x D
0,3 x D
90 – 150
60 – 100
fz
fz
0,054
0,048
0,062
0,056
0,077
0,070
0,083
0,076
0,088
0,081
1 Ap1 max
0,3 x D
90 – 115
fz
0,061
0,070
0,087
0,095
0,101
M 2 Ap1 max
0,3 x D
60 –
80
fz
0,048
0,056
0,070
0,076
0,081
3 Ap1 max
0,3 x D
60 –
70
fz
0,040
0,047
0,057
0,061
0,065
1 Ap1 max
0,3 x D
50 –
90
fz
0,061
0,070
0,087
0,095
0,101
2
S
3
Ap1 max
Ap1 max
0,3 x D
0,3 x D
25 –
60 –
40
80
fz
fz
0,032
0,048
0,037
0,056
0,046
0,070
0,050
0,076
0,054
0,081
4 Ap1 max
0,3 x D
50 –
60
fz
0,045
0,052
0,064
0,069
0,074
1
H
2
Ap1 max
Ap1 max
0,3 x D
0,3 x D
80 – 140
70 – 120
fz
fz
0,054
0,040
0,062
0,047
0,077
0,057
0,083
0,061
0,088
0,065
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for nishing applications or for lower hardness (machinability) within group.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on >12mm diameters.
Series 77NE • VariMill III ER • With Neck • Finishing • Victory Grades
Side Milling (A)
WS15PE
Recommended feed per tooth (fz = mm/th) for side milling (A).
Material
Group
A
ap ae
Cutting Speed — vc
m/min
min max
mm
10,0
D1 — Diameter
12,0 16,0 18,0
20,0
4 Ap1 max 0,06 x D 180 – 300
P
5 Ap1 max 0,06 x D 120 – 200
fz
fz
0,065
0,058
0,075
0,067
0,092
0,084
0,099
0,091
0,106
0,097
1 Ap1 max 0,06 x D 180 – 230
fz
0,073
0,084
0,105
0,113
0,121
M 2 Ap1 max 0,06 x D 120 – 160
fz
0,058
0,067
0,084
0,091
0,097
3 Ap1 max 0,06 x D 120 – 140
fz
0,048
0,056
0,068
0,073
0,078
1 Ap1 max 0,06 x D 100 – 180
fz
0,073
0,084
0,105
0,113
0,121
2 Ap1 max 0,06 x D 50 – 80
S
3 Ap1 max 0,06 x D 120 – 160
fz
fz
0,038
0,058
0,045
0,067
0,056
0,084
0,060
0,091
0,065
0,097
4 Ap1 max 0,06 x D 100 – 120
fz
0,053
0,062
0,077
0,083
0,089
1 Ap1 max 0,06 x D 160 – 280
H
2 Ap1 max 0,06 x D 140 – 240
fz
fz
0,065
0,048
0,075
0,056
0,092
0,068
0,099
0,073
0,106
0,078
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for nishing applications or for lower hardness (machinability) within group.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on >12mm diameters.
O46
zakaz@widiahanita.ru
www.widiahanita.ru